Cisco Anyconnect Secure Mobility Client Ubuntu



Just in case you do want the Ciso Anyconnect client working take a look at this blog. Just disable the Firefox Iced Tea web plugin and go to your VPN site. Have Ubuntu download the VPN installer and run the shell script. In my case Cisco Anyconnect VPN client was installed and available under the Internet section and works fine. Use the GUI App to install the Cisco AnyConnect Diagnostic and Reporting Tool. If the GUI installation doesn’t work, run the commands below to install it. That should install AnyConnect for you including DART After that, Cisco AnyConnect Secure Mobility Client should be ready to use. Introduction This document describes a configuration example for Adaptive Security Appliance (ASA) Cisco AnyConnect Secure Mobility Client access that uses client certificate for authentication for a Linux Operative System (OS) for an AnyConnect user to connect successfully to an ASA Headend. Contributed by Dinesh Moudgil, Cisco HTTS Engineer.

As part of its ongoing cybersecurity strategy, The Division of Information Technology has implemented a mandatory two-factor authentication for the Enterprise Virtual Private Network (VPN)

What is two-factor authentication?Cisco anyconnect mobility client download 4.5

To increase security measures on your account, two-factor authentication requires two steps to log in. The first step is using something you know (i.e., your password), and the second step is something you have (i.e., cell phone) to securely verify your identity.

What is required to use the VPN?
  • Enroll your phone for two-factor
  • Cisco AnyConnect client

AnyConnect

FIU implements the AnyConnect VPN client to allow FIU users to connect on and off campus to the FIU network through a Secure Socket Layer (SSL) protocol.

  • Supported Operating Systems
  • System Requirements
  • AnyConnect Clients
  • Installing the AnyConnect

Supported Operating Systems

Microsoft Windows

  • Windows 10 (32-bit and 64-bit)
  • Windows 8, 8.1 (32-bit and 64-bit)
  • Windows 7 (32-bit and 64-bit)

MAC OS X

  • Mac OS X 10.11, 10.12, 10.13, 10.14 x86 (32-bit) or x64 (64-bit)
  • Mac OS X versions 10.10 and lower are no longer supported

Linux

  • Linux
  • Red Hat Enterprise Linux 6.x and 7.x (64-bit)
  • Ubuntu 14.04 (LTS), 16.04 (LTS), and 18.04 (LTS) (64-bit only)

System Requirements

Microsoft Windows

  • Pentium class processor or greater.
  • 100 MB hard disk space.
  • Microsoft Installer, version 3.1.

MAC OS X

  • 50MB of hard disk space.
  • To operate correctly with Mac OS X, AnyConnect requires a minimum display resolution of 1024 by 640 pixels.

Linux

  • x86 instruction set.
  • 32-bit or 64-bit processor.
  • 32 MB RAM.
  • 20 MB hard disk space.
  • Superuser privileges are required for installation.
  • libstdc++ users must have libstdc++.so.6(GLIBCXX_3.4) or higher, but below version 4.

AnyConnect Clients

MAC OS X

  • Intel download 4.9.X

AnyConnect Secure Mobility Client for Android Devices

All Android AnyConnect packages are available for installation and upgrade from the Google Play Store

For additional information regarding supported Android devices, please visit Cisco's support documentation

AnyConnect Secure Mobility Client for Apple Devices

Cisco Anyconnect Secure Mobility Client Ubuntu

All Apple AnyConnect packages are available for installation and upgrade from the Apple App Store

For additional information regarding supported Apple devices, please visit Cisco's support documentation

Mobility

TwoFactor

Enroll

In order to verify your identity, you will be required to enroll your phone (“something you have”) in FIU’s two-factor authentication system.

Please review these simple step-by-step instructions below to enroll your phone:

  • Visit login.fiu.edu/enroll
  • Log in using your FIU username and password
  • When prompted, enter the phone number of the device you would like to enroll in two-factor authentication (FIU numbers will not be accepted).
  • Specify what type of device corresponds to the enrolled number
  • When prompted, enter the code you received
  • You are now enrolled in two-factor authentication

TwoFactor with VPN

Launch your Cisco AnyConnect VPN client, you will be prompted for your FIU username, password, and a “second password”. In this second password field, you will specify your preferred verification method (“something you have”).

In the second password field, you will be required to type “push”, “phone”, or “sms”.

  • Push: uses the DUO Mobile app *
  • Phone: places an automated voice call *
  • SMS: sends unique verification codes via text messages **

(*Note: Your carrier’s data and message rates may apply)

(**Note: Your carrier’s data and message rates may apply, 10 codes are sent in one text message to use 10 different times.)

Signing into Any Connect VPN using Two-Factor

FAQs

What is SSL VPN?
SSL VPN is a client application used to connect to the VPN. This is an application, which gets installed on the computer. This client has support for 64bit systems. This is also known as the AnyConnect client.
What is my username and password?
Use your My Accounts username and password to access the FIU VPN.Visit https://myaccounts.fiu.edu for additional information.
I need to access systems behind a firewall what vpn would be best to use?
AnyConnect client.
Can I use VPN on my iphone?
Yes. Please look above for supported devices.
Windows Anyconnect Client Installation

Windows Vista/7/8/8.1/10 (32 or 64 bit) Anyconnect Client Installation

  1. Browse to NS VPN Client Download Page
  2. Start the 'anyconnect-win' installer downloaded in step 2.
  3. At each prompt, click 'Next.' You may see a 'User Account Control' dialog box asking if you would like to install the program. Click 'Yes.'
  4. Once the install is complete, click 'Finish.'
  5. Start the 'anyconnect-win-gina' installer downloaded in step 2.
  6. At each prompt, click 'Next.' You may see a 'User Account Control' dialog box asking if you would like to install the program. Click 'Yes.'
  7. Once the install is complete, click 'Finish.'
  8. The machine will now ask to reboot. Click yes to reboot.
  9. Launch the client by going to Start->All Programs->Cisco->Cisco Anyconnect Secure Mobility Client
  10. In the field to the left of the 'Connect' button, click on the text area and type 'vpn.ufl.edu'. Click connect.
  11. Authenticate with your gatorlink ID (in the form of username@ufl.edu) and your gatorlink password. Click OK.
  12. The most recent version of the client and vpn configuration files will be automatically downloaded. This may require another reboot to complete the update.
  13. Your client is now ready for use.

Notes:

Cisco Anyconnect Secure Mobility Client Ubuntu 18

  • Once the Anyconnect is installed on your machine, it will always be automatically upgraded to the latest version as they are published by Network Services. You shouldn't need to go through the manual installation process unless you reinstall your operating system, or your client becomes corrupted and needs to be uninstalled and reinstalled.
  • After connecting for the first time, the VPN policy will be pushed to your client. The pulldown will say 'Gatorlink VPN' rather than vpn.ufl.edu after this policy is downloaded.




Comments are closed.